Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
What are your thoughts and feelings on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably challenging job. If the old tub is easily easily accessible, the job can move immediately; if you need to open up a wall surface to eliminate the old tub as well as position the new bathtub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also embeded in the brand-new one. Ensure you have qualified on your own for the task as well as are comfortable trying it. Instead of employing a professional to take over a halfway-completed task, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub and also don't need to transform the setup of your previous water system pipes.
Your tools and also material checklist need to consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the restricted accessibility that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in area in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wooden boards under its feet, put the tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the other faucet.
Activate the water supply and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub should wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bathroom as well as the tiling, bring about problems with wetness and possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads on How to Install a Bathtub, I was thinking sharing that piece of content was a great idea. I beg you take the opportunity to share this blog entry if you liked it. Thank you for your time spent reading it.
View Website Report this page